Competitive PVC Pipe Prices

We stock a wide range of PVC pipe and fittings which are available separately or in kits designed specifically for our central vacuum systems.

Pipe Fitting Kits


			SPF - starter kit - £43.00 + VAT 10 x 45°MF bends 10 x 45°FF bends 5 x straight connectors 10 x pipe clips exhaust flap pot of glue & 10m of low voltage cable NB. Picture shows SPF kit and one white Millennium socket and M90 (as there is a wide choice of sockets they are not supplied with the kit and must be ordered separately)


	PF2 - fitting kit for 2 sockets - £34.00 + VAT 2 x 45° Tee connector 6 x 45°MF bends 4 x 45°FF bends 10 x straight connectors 6 x pipe clips 15m of low voltage cable NB. Picture shows PF2 kit plus a pair of white Millennium sockets and two M90s (as there is a wide choice of sockets they are not supplied with the kit and must be ordered separately)


			PF3 - fitting kit for 3 sockets - £53.50 + VAT 3 x 45° Tee connector 9 x 45°MF bends 6 x 45°FF bends 15 x straight connectors 10 x pipe clips 25m of low voltage cable NB. Picture shows PF3 kit and 3 white Millennium sockets and three M90s (as there is a wide choice of sockets they are not supplied with the kit and must be ordered separately)

	PP6 - pipe kit - £13.00 + VAT 6m pack of 50mm (OD) PVC pipe in 5 x 1.2m lengths PP12 - pipe kit - £25.75 + VAT 12m pack of 50mm (OD) PVC pipe in 10 x 1.2m lengths

	The following fittings are also available separately:

45TEE

45FF

45MF

45 degree male/female elbow. 91p + VAT

45 degree female/female elbow. 91p + VAT

45 degree Tee connector. £1.97 + VAT

M90

50S

WIRE100

CL50

50mm pipe clip. 48p + VAT

Low voltage cable to be installed alongside the PVC pipe. £5.57 + VAT per 10 metres

50mm straight connector. 65p + VAT

90 degree elbow for socket where pipe is run within the wall. £3.98 + VAT

	The following fittings can be used as alternatives to the 90 degree elbow:-

MTEE

90MF

MST

Straight fitting - use with the 90MF (on the left) to run pipe to socket through a wall. £3.98 + VAT

In-line Tee fitting for pipework running within the wall. £3.98 + VAT

90 degree male/female elbow for use with MST fitting (on the right) only where the pipe runs behind the wall, not within the wall. 91p + VAT

	The following fittings are also available:-

SILENCER
		CL100


	The silencer, which has an outer diameter of 100mm, is fitted onto the exhaust of the vacuum unit and reduces the noise of the air being ducted to the outside. £17.90 + VAT. It is normally held in place with 2 clamps (CL100) £1.60 + VAT each


		SCRC
22FF 22 degree female/female elbow. £1.02 + VAT


	The screw end cap (SCRC) is used in connection with a TEE fitting permitting access to the system if required. £1.85 + VAT

EXOW

90T50

The 90T50 is shown here with a screw end cap. It can also be used as a TEE fitting where the run of pipe is installed behind the wall. It would be connected to the socket with a short length of 50mm pipe and a straight fitting (either MST or DST depending on the choice of socket front. If the run of pipe ends at this socket then you would normally use a 90FF unless access is required as shown - see Installation Guide page 5

90FF

An exhaust flap should be fitted on the outside wall, where the vacuum exhaust has been ducted. £2.65 + VAT. It is also supplied in our starter pipe fitting kit (SPF)

91p + VAT

£1.97 + VAT

All pipework and fittings can be purchased separately at very competitive prices. This pipework is not only for vacuum systems but can also be used for waste pipes, rain water pipes, etc.

	Copyright (c) 2003-8 CVC Direct Ltd. All Rights Reserved.